All Wheel Drive Club

Suzuki 4x4 Club™
Dedicated to all Suzuki 4x4 Owners
 
 FAQFAQ   SearchSearch   Watched TopicsWatched Topics   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your personal messagesLog in to check your personal messages   Log inLog in 
suzuki 4x4 club forumsSuzuki 4x4 Forums   CalendarCalendar  Suzuki 4x4 Club ShopClub Shop  Suzuki 4x4 Classified Ads serviceClassified Ads
Suzuki 4x4 HomeSuzuki 4x4 Home   dynamic online chat serviceChatrooms  Yellow Diamond ClubsYellow Diamond Clubs

Bull bars font fit


 
Post new topic   Reply to topic    Suzuki 4x4 Club™ Forum Index -> Bodywork & trim
View previous topic :: View next topic  
Author Message
desired_affect
*


Joined: 01 Apr 2010
Posts: 49
Location: ipswich

PostPosted: Mon Apr 11, 2011 5:49    Post subject: Bull bars font fit Reply with quote

I've brought a set of bull bars from. Sj140 for my sammy but they don't seem to want to go on.
The brackets don't fit in the box section on the chassi they will only fit onthe inside egde but this isn't far enoughout.
Any one had a similar problem??[marq=down]
Back to top
View user's profile Send personal message MSN Messenger
Google
Sponsor





PostPosted: Mon Apr 11, 2011 5:49    Post subject: Google Ads keep this community free to join!


Back to top
zocko
*******


Joined: 13 Sep 2009
Posts: 1438
Location: Southampton

PostPosted: Sun Apr 17, 2011 22:26    Post subject: Reply with quote

try putting the brackets on the chassis before you bolt them to the bull bar, you might find theyre on the wrong side of the bull bar uprights?
_________________
the car in front is a toyota...

the car pulling it out of the mud is a suzuki
Back to top
View user's profile Send personal message
desired_affect
*


Joined: 01 Apr 2010
Posts: 49
Location: ipswich

PostPosted: Mon Apr 18, 2011 5:57    Post subject: Reply with quote

The problem is they want to fit on the outside of the box section but there is a bit of wavey metal on the chassie in the way, the brackets won't fit inside to box section either but will fit to the inside edge of the box section. The brackets are then to close together and won't bolt on the bull bars.
Back to top
View user's profile Send personal message MSN Messenger
SWeed2k1
**


Joined: 12 Apr 2011
Posts: 50
Location: Drummuir, scotland

PostPosted: Mon Apr 18, 2011 12:21    Post subject: Reply with quote

i had the same problem. i fitted my one my sacking the brackets and welding 2 bits of angle to the front of the chassis and then bolting the bar to it. as its at the bottom/under the bumper you don't see it. and its been thro a mot since then
Back to top
View user's profile Send personal message MSN Messenger
desired_affect
*


Joined: 01 Apr 2010
Posts: 49
Location: ipswich

PostPosted: Mon Apr 18, 2011 12:44    Post subject: Reply with quote

SWeed2k1 wrote:
i had the same problem. i fitted my one my sacking the brackets and welding 2 bits of angle to the front of the chassis and then bolting the bar to it. as its at the bottom/under the bumper you don't see it. and its been thro a mot since then


Would you possibly be able to sent a picture.
Back to top
View user's profile Send personal message MSN Messenger
SWeed2k1
**


Joined: 12 Apr 2011
Posts: 50
Location: Drummuir, scotland

PostPosted: Mon Apr 18, 2011 15:23    Post subject: Reply with quote

Back to top
View user's profile Send personal message MSN Messenger
desired_affect
*


Joined: 01 Apr 2010
Posts: 49
Location: ipswich

PostPosted: Wed May 18, 2011 15:53    Post subject: Reply with quote

SWeed2k1 wrote:
i had the same problem. i fitted my one my sacking the brackets and welding 2 bits of angle to the front of the chassis and then bolting the bar to it. as its at the bottom/under the bumper you don't see it. and its been thro a mot since then


Well I finally got round to putting them on, this was my solution.


Just need to get it all painted now
Back to top
View user's profile Send personal message MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic    Suzuki 4x4 Club™ Forum Index -> Bodywork & trim All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

All contents © Hobson's Choice IT Solutions Ltd 1997 on
Powered by phpBB © 2001, 2005 phpBB Group